Splice plate galvinized steel install#
Splice plate galvinized steel code#
Splice plate galvinized steel free#

We have not attached the bottom or top plates. We then do the rest of the verticals OC and nail them in. Once we have the wall level and our boards are OC at 16 we now have a moveable wall piece that we can make slight adjustments to. Then minus three inches, make our two cut and slide those in snuggly. We measure floor to joist on each side - one joist over.

Splice plate galvinized steel install#

Mainly because the heights differ and I want my install snug. When we are framing basements we build upright. Lay down a chalk line on the floor for long walls. You do not want any of the framing touching the wall. Start at the bulge or give yourself adequate space.

If you are doing a long wall most basement walls bulge. In essence almost everything you are worrying about is for framing that is load bearing - for you this does not matter. I have had maybe 2 inspectors out of 50 ever care.

Some inspectors make sure that there are two points engagement on both the bottom and top plates every span or 8 feet. If memory serves me 16 is needed for drywall but 24 for paneling. And when I say I don't worry about it is because all basements we do are either 16 or 12 so I have never gone back to see if 24 or 18 is code.

Splice plate galvinized steel code#

I am not sure if it is code yet because I would never worry about the code but all places that I have done basements require 16' or less. TABLE R602.3.2 SINGLE TOP-PLATE SPLICE CONNECTION DETAILSĬONDITION TOP-PLATE SPLICE LOCATION Corners and intersecting walls Butt joints in straight walls Splice plate size Minimum nailsĮach side of joint Splice plate size Minimum nailsįor SI: 1 inch = 25.4 mm, 1 foot = 304.8 mm.īasement framing is 100% cosmetic. Omission of the top plate is permitted over headers where the headers areĪdequately tied to adjacent wall sections in accordance with Table R602.3.2. The rafters or joists shall be centered over the studs with a tolerance ofģ. In-line splices in straight wall lines in accordance with Table R602.3.2.Ģ. The single top plate shall be tied at corners, intersecting walls, and at Nominal thickness and have a width not less than the width of the studs.Įxception: A single top plate used as an alternative to a double topġ. Plates shall be not less than 2-inches (51 mm) Top plates shall be offset not less than 24 inches (610 mm). Overlapping at corners and intersections with bearing partitions. Wood stud walls shall be capped with a double top plate installed to provide What do the plates look like for the corners and T-intersections? Is that ok? Exception #2 makes this a little fuzzyģ) For the long stretches I've seen the rectangular splice plates referenced in the table. I was planning on doing a single top plate and was looking at the code, but have some questions:ġ) If I have a single top plate, does it matter where the seam is? Is there any restrictions or preferences?Ģ) My joists are 24' oc, but I was planning on doing 16' oc walls. For many walls, I was thinking of putting up two 8' or 10' walls with the stud straddling both walls. *Check availability of non-standard finishes with your Unistrut distributor.I'm trying to build walls for my basement, and not surprisingly, many walls are longer than 8/10/12/16ft. Some may also be available in Hot-Dipped Galvanized, Plain Carbon Steel, or Stainless Steel (Types 304 & 3016). Most flat plate fittings are available in the standard Unistrut finishes: Electro-Galvanized and Perma Green.

Splice plate galvinized steel free#

The pickling of the steel produces a smooth surface free from scale.

The fitting steel also meets the physical requirements of ASTM A1011 SS GR33.

Splice plates are ideally joined to sections of strut using 1/2' hex head cap screws and 1/2' spring nuts (or other variety of Unistrut channel nut), for a unique, weldless connection.Īs with all Unistrut fittings, flat plate fittings are made from hot-rolled, pickled and oiled steel plates, strip or coil, and conform to ASTM specifications A575, A576, A636, or A36. That is because their primary use is to join – or splice – channel sections together.įlat plate fittings are sheared from 1/4' thick plate steel and punched with 9/16' holes. You may have heard Unistrut flat plate fittings referred to as 'Splice Plates'. Within the Unistrut Metal Framing System there are many different categories of parts, each with their own function, this week we’ll discuss Unistrut Flat Plate Fittings. Flat Plate Fittings are primarily used to join sections of Unistrut Channel together